Automobile fuse inspection and replacement.ceramic fuse for microwave_Industry Trends_News & Events_XC Electronics(Shenzhen)Corp.,LTD

中文

Online Message

11 2023-07

Share:

　　

　　If any electrical equipment does not work during the use of the car, it may be caused by a burnt fuse and needs to be replaced in a timely manner.

　　The method is: 1. Turn off the ignition switch and open the fuse box cover. 2. Replace the fuse.

　　Precautions:

　　(1) Replace the fuse according to the rated current value indicated on the fuse box cover, and do not use a fuse with a higher rated current.

　　(2) If the new fuse immediately blows again, it indicates that there may be a malfunction in the circuit system and should be repaired as soon as possible.

　　(3) In the absence of backup fuses. In case of emergency, fuses on other equipment that have no impact on driving and safety can be replaced.

　　(4) If a fuse with the same current load cannot be found, a lower rated current than the original fuse can be used instead.

Read recommendations:

JK-SMD 1812 Series

fuse box fuse replacement

thermal overload protector in motor

Use and maintenance of fuses and fuses.resettable fuse datasheet

PREVIOUS:Plug type fuse.motor blows fuse on startup

Return

Next：Auto fuse.solar panel fuse location

Related News

September 11,2023

How to Realize the Protection Function of PTC Self Recovery Fuses.mini blade fuse vs standard

　　　　How does PTC self recovery fuse achieve protection function? The actual process of PTC overcurrent circuit protection is not yet clear, and its superiority needs further exploration. So far, it is believed that PTC is a polymer based self recovery fuse that can limit current.　　The principle of PTC self recovery fuse is to limit potentially harmful overload currents within a safe range. Specifically, excessive current flowing through the device can lead to an increase in internal heat (I2R), resulting in a temperature rise in PTC and an increase in its resistance. Before overheating occurs, PTC resistance usually only accounts for a small portion of the total impedance of the circuit. The increase in resistance of polymer PTC self-healing fuses has a non-linear characteristic, and such relatively large resistance will reduce or limit the current in the circuit to a safe range. The transition point from low resistance to high resistance is called the "jump point".　　The heat generated

July 12,2023

The difference between fuses and circuit breakers.chip fuse please replace ic

　　　　Their common feature is that they can all achieve short-circuit protection. The principle of a fuse is to use current to flow through the conductor, causing it to heat up. After reaching the melting point of the conductor, the conductor melts, so disconnecting the circuit protects electrical appliances and circuits from being burned out. It is an accumulation of heat, so overload protection can also be achieved. Once the melt burns out, it needs to be replaced.　　A circuit breaker can also achieve short-circuit and overload protection for circuits, but the principle is different. It achieves circuit breaker protection through the bottom magnetic effect of the current (electromagnetic release), and overload protection through the thermal effect of the current (not fusing, and there is often no need to replace components). In practice, when the electrical load in the circuit approaches the load of the fuse used for a long time, the fuse will gradually heat up until it blows. As mentio

August 16,2023

Three major factors affecting the lifespan of fuses.max fuse size meaning

　　　　1. Working environment temperature: Excessive ambient temperature can damage the lifespan of fuses. Slow melting fuses, such as tin ball type, begin to diffuse towards the metal wire when the temperature is about 160 ℃ (150-170 ℃); The temperature at which the melt of a fast melting fuse begins to undergo severe oxidation is approximately 200 ℃ (175-225 ℃). With the oxidation of the fuse from the outside to the inside, multiple diffusion, thermal stress fatigue, etc., the lifespan of the fuse will gradually shorten. Therefore, it is recommended that the delay type fuse fuse should not work above 150 ℃ for a long time, and the fast melting type fuse should not work above 175~225 ℃ for a long time.　　2. Pulse current: Pulse impact can generate thermal cycling, leading to diffusion, oxidation, thermal stress, and even acceleration of the fuse. The fuse will gradually age with increasing pulse energy and frequency. The impact resistance life of a fuse depends on the percentage of I2t of

November 06,2023

temperature switch thermostat thermal protector fuse.Micro fuse

　　　　A professional enterprise engaged in the research and development, production, and sales of patch fuses and plug-in fuses. All products meet the requirements of lead-free and halogen-free environmental protection, and have obtained foreign authoritative safety certification such as UL, VDE, TUV, etc. The products are widely used in industries such as computers, communication, security, automobiles, toys, and household appliances.　　Main supply products: self recovery fuses, disposable fuses, patch fuses, plug-in fuses, Litteluse Litteluse fuses.　　The miniature fuse meets the following conditions:　　1. Power on capacity: Power on at rated current for 1 hour without fusing.　　2. Temperature rise: When energized according to the rated current, the ground temperature rise is less than 75 ℃.　　3. Fusing test: Fusing within 1 minute at twice the rated current.　　4. Breaking capacity: When the rated breaking capacity is added, there will be no continuous arcing or ignition.　　This product can b

November 10,2023

bs 1362 fuse operation characteristics.The difference between self recovery fuse and blown fuse

　　　　In the circuit protection scheme, is it better to choose a self recovery fuse or a blown fuse for overcurrent protection? This issue has always been a serious issue that electronic security engineers must take seriously, and it is also one of the many questions that buyers consult with. In smart consumer electronics products (such as computers, smartphones, tablets, etc.), circuit protection design requires the use of self-healing fuses. If a blown fuse is used, it needs to be replaced every time abnormal overcurrent occurs, which is unacceptable to end users. In situations where safety needs to be prioritized or damage to other downstream circuit equipment needs to be avoided, it is better to choose a fused fuse. In case of a fault, completely cutting off the current is beneficial for fault diagnosis.　　So, what is the difference between a self restoring fuse and a blown fuse? Dongwo Electronics, a comprehensive manufacturer of circuit protection components, has rich practical appl