Automotive fuse box.15a pptc fuses_Industry Trends_News & Events_XC Electronics(Shenzhen)Corp.,LTD

中文

Online Message

18 2023-07

Share:

　　

　　Car fuse box is a box used to install car fuses. According to the size of the installed fuse, it can be divided into: small car fuse boxes; Medium size car fuse box; Large car fuse box. General injection molding materials include: PBT engineering plastics, each with varying degrees of high temperature resistance. When selecting a car fuse box, consideration should be given to the current size of the car fuse used, the size requirements of the fuse, and the selection of different fuse boxes. The English translation of automotive fuse box is:

　　Classification of automotive fuse boxes:

　　According to the classification of installed fuses, they can be divided into fuse box and fuse box

　　According to the size of fuses, they can be divided into large fuse boxes, medium fuse boxes, and small fuse boxes

　　According to material classification, it can be divided into plastic fuse boxes and bakelite fuse boxes

　　According to environmental protection, it can be divided into environmentally friendly fuse boxes,

　　According to installation method, it can be divided into wire type fuse box and circuit board type fuse box, and instrument panel installation fuse box

Read recommendations:

adjustable bimetal thermostat switch

Regarding the issue of 20A internal fuse clip.fuse clips hs code

PREVIOUS:Action temperature of NEC Thermal cutoff.thermal controller alienware

Return

Next：Thermal cutoff NEC.best hair thermal protector

Related News

October 11,2023

test auto fuse with multimeter.The application of self recovery fuse in rechargeable battery pack

　　　　1. The application of self recovery fuse in rechargeable battery pack　　1) Problem and Analysis: NICD, NiMH, and Li-ION are commonly used in special protection circuits for mobile phones and computers. The reasons for these battery pack failures are usually: unexpected short circuit between the positive and negative terminals; The charger cannot stop charging a fully charged battery; The polarity of the wrong charger or battery is reversed. Installing the PTC patch series in series in various units of the battery pack can provide overcurrent and over temperature protection for the circuit.　　2) Protection requirements: In the event of a malfunction, the voltage of the mobile phone can reach 16V, and the voltage of the computer can reach 24V; Its current can reach 100 amperes. In overcharging conditions, the battery pack needs to be protected against overheating. NiCD batteries cannot exceed 120C, and NiMH and Li Ion batteries cannot exceed 90C.　　The ultra small package (0402 specific

July 10,2023

Precautions for using fuses and fuses.charger fuse box diagram

　　　　Precautions for using fuses:　　1. The protective characteristics of the fuse should be adapted to the overload characteristics of the protected object. Considering the possible short-circuit current, a fuse with corresponding breaking capacity should be selected;　　2. The rated voltage of the fuse should adapt to the line voltage level, and the rated current of the fuse should be greater than or equal to the rated current of the melt;　　3. The rated current of each level of fuse melt in the circuit should be matched accordingly, and the rated current of the previous level of melt must be greater than the rated current of the next level of melt;　　4. The melt of the fuse should be matched according to the requirements, and it is not allowed to arbitrarily increase the melt or use other conductors to replace the melt.　　Inspection of fuses:　　1. Check whether the rated values of fuses and melts match the protected equipment;　　2. Check the appearance of the fuse for damage or deformation, a

August 13,2024

Principle of action of resettable fuse

　　　　The working principle of a resettable fuse is the dynamic balance of energy. The current flowing through the resettable fuse generates a certain degree of heat due to the thermal effect of the current (there is a resistance value in the resettable fuse). All or part of the heat generated is dissipated into the environment, but the remaining heat will increase the temperature of the resettable fuse element.　　During normal operation, the temperature is low and the heat generated and dissipated reaches equilibrium. When the resettable fuse is in a low resistance state, it does not work. When the current flowing through it increases or the ambient temperature rises, if the generated and dissipated heat reaches equilibrium, the fuse will remain inactive.　　If the current or temperature continues to rise at this time, the heat generated will be greater than the heat dissipation, causing a sharp increase in the temperature of the resettable fuse. Therefore, small temperature changes will l

July 12,2023

The difference between fuses and circuit breakers.chip fuse please replace ic

　　　　Their common feature is that they can all achieve short-circuit protection. The principle of a fuse is to use current to flow through the conductor, causing it to heat up. After reaching the melting point of the conductor, the conductor melts, so disconnecting the circuit protects electrical appliances and circuits from being burned out. It is an accumulation of heat, so overload protection can also be achieved. Once the melt burns out, it needs to be replaced.　　A circuit breaker can also achieve short-circuit and overload protection for circuits, but the principle is different. It achieves circuit breaker protection through the bottom magnetic effect of the current (electromagnetic release), and overload protection through the thermal effect of the current (not fusing, and there is often no need to replace components). In practice, when the electrical load in the circuit approaches the load of the fuse used for a long time, the fuse will gradually heat up until it blows. As mentio

October 28,2023

very fast acting fuse.Why do fuses have high resistivity

　　　　Fuses, also known as current fuses, are defined as "fuse links" in the IEC127 standard. It mainly serves as overload protection. If the fuse is correctly placed in the circuit, the Shenzhen fuse will fuse and cut off the current when the current abnormally rises to a certain height and heat, protecting the safe operation of the circuit.　　More than a hundred years ago, the fuse invented by Edison was used to protect expensive incandescent lamps at that time. With the development of the times, the fuse protected electrical equipment from overheating and prevented serious damage caused by internal faults in electronic equipment.