very fast acting fuse.Why do fuses have high resistivity_Industry Trends_News & Events_XC Electronics(Shenzhen)Corp.,LTD

中文

Online Message

28 2023-10

Share:

　　 1a47df70812c6ad

　　Fuses, also known as current fuses, are defined as "fuse links" in the IEC127 standard. It mainly serves as overload protection. If the fuse is correctly placed in the circuit, the Shenzhen fuse will fuse and cut off the current when the current abnormally rises to a certain height and heat, protecting the safe operation of the circuit.

　　More than a hundred years ago, the fuse invented by Edison was used to protect expensive incandescent lamps at that time. With the development of the times, the fuse protected electrical equipment from overheating and prevented serious damage caused by internal faults in electronic equipment.

Read recommendations:

slow blow glass fuse

A Brief Discussion on the Future Development of Recoverable Fuses

The Application of Self Recovery Fuses in RS485 Interface.volvo truck blower motor fuse location

PREVIOUS:tvms output fuse blown.How to determine the fuse in the circuit?

Return

Next：waterproof fuse block.Why do fuses have high resistivity

Related News

July 19,2023

Breaking capacity of glass sealed fuse.ptc reset fuse

　　　　Also known as rated short-circuit capacity, it refers to the maximum current value (AC is the effective value) that a fuse can safely break under rated voltage. It is an important safety pointer for fuses. The code for breaking capacity is Ir.　　That is, the time/current characteristic (also known as the ampere second characteristic). There are usually two expression methods, namely I-T diagram and test report. The I-T diagram is a curve formed by connecting the average fusing time coordinate points of fuses under different current loads in a coordinate system composed of load current as the x coordinate and fusing time as the y coordinate. Each model and specification of fuse has a corresponding curve that represents its fusing characteristics. This curve can be used as a reference when selecting fuses. A test report is a record of test data conducted in accordance with standard requirements for testing projects. Our I-T chart and test report are both based on the data measured und

September 22,2023

Surface Mount Fuses.motorcycle fuse block with relay

　　　　1. The location where the patch fuse is connected to the circuit　　When connecting patch fuses in a circuit, it is important to be careful not to connect the fuse to the neutral or ground wire. The correct connection is to connect it to the live wire, so that when the circuit is overloaded, the fuse can be blown in a timely manner to protect circuit safety. If only connected to the neutral line or ground wire, the fuse should blow in a timely manner, but the voltage carried by the positive and negative poles through the live wire may also cause the circuit to burn out. Therefore, the priority order for fuses to be connected to the circuit is the live wire, neutral wire, and ground wire.　　The location where the fuse is connected to the circuit　　2. Connection method of patch fuse in circuit　　Usually, fuses are connected in series in a circuit. If the fuses are connected in parallel in the circuit, the current cannot be disconnected in a timely manner in case of abnormal conditions in

February 27,2024

reset motor thermostat on shark vacuum.The resistance value of the fuse resistance

　　　　The resistance value of the fuse resistor is relatively small, generally ranging from 0.33 Ω to 10K Ω, and the power is also small.　　Attachment 1: Differences between current fuses and wire wound fuse resistors　　1. The current fuse does not consume energy, generate heat, or melt, and the latter will not melt when the resistance value is selected higher.　　2. The current fuse is short and cannot be adjusted, and the resistance value is not optional. The latter has an adjustable fuse length and resistance value.　　3. The use of current fuses should be coordinated with NTC, which can be used separately.　　4. The current fuse does not absorb abnormal surges and lightning surges, while the latter can absorb and have strong resistance to lightning surges and abnormal surges.

September 09,2024

How to choose fuses for blockage experiments

　　　　Rated current: Understanding the rated current of the equipment or motor you are testing is crucial. The rated current of the fuse should be greater than the rated current of the equipment to ensure that the fuse will disconnect the circuit and provide overload protection when the current exceeds the set threshold during the experiment.　　Short circuit protection: In the stall experiment, the equipment may generate huge currents due to overload or stall. It is important to choose fuses with lower melting current and fast melting characteristics to prevent equipment from overheating or damage.　　Freeze voltage: Select the fuse according to the voltage requirements of the equipment. The freeze voltage of the fuse should match the operating voltage of the equipment to ensure that the fuse can function properly during the experiment.　　Temperature characteristics: In the stall experiment, the equipment may generate high temperatures. Choosing fuses with appropriate temperature coefficient

October 10,2023

Selection of fuse type.motorcycle fuse box waterproof

　　　　Select the type of fuse based on the electrical load characteristics in the circuit (slow melting or fast melting fuse). Fuses can be divided into slow fuse and fast fuse according to their different fusing characteristics. Fast melting fuses are commonly used in resistive circuits to protect components that are particularly sensitive to current fluctuations; Slow melting fuses are commonly used to quickly disconnect circuits when there is a fault with a large surge current when the circuit status changes.　　Finally, according to the sensitivity/capacitance circuit (such as the fan motor circuit), it can withstand the impact of surge pulses when switching on and off the machine, and the appropriate fuse type of structure is selected for the actual assembly position where the fuse wire appears. Priority should be given to fuses that occupy little space after installation.