thermal sensor for human detection_mini cooper fuse box factory_XC Electronics(Shenzhen)Corp.,LTD

中文

Online Message

20 2024-08

Share:

　　self recovery fuse will still activate protection again after being powered on again.

　　Here are a few knowledge points about self-healing fuses that need to be sorted out:

　　1. Self recovering fuses are different from traditional one-time blown fuses, as they can protect circuits multiple times without the need for disassembly and replacement.

　　2. After the self recovery fuse is activated for protection, the circuit is not completely interrupted, and there is still a small current in the circuit. The current is very weak, which can keep the self recovery fuse in a protected state. At this time, other devices on the circuit cannot work.

　　3. The main changes before and after the self recovery fuse starts protection are that the temperature before protection is at room temperature, and after protection, the temperature rises, and the internal temperature reaches 130 ℃.

　　4. After the self recovery fuse is activated for protection, the equipment stops working and needs to be manually powered off first. After troubleshooting, the circuit can be restored to normal operation.

　　5. The process of restoring a self recovering fuse is the process of lowering its own temperature. After a power outage, there is no current passing through and it no longer generates heat. The heat dissipation restores the temperature and state before starting.

Read recommendations:

craftsman radial arm saw fuse

mini vs micro blade fuse

heater fan surge protector

Classification of fuses and fuses.where is the air conditioner fuse located

1206 Volume 1A Disposable Quick Blown Fuse Specification Parameters.40 amp blade fuse

PREVIOUS:plastic fuse box regulations

Return

Next：30 amp screw in resettable fuse

Related News

October 11,2024

ecopure water heater protector.Working Principle and Application Scenarios of Current Fuses

　　Working Principle and Application Scenarios of Current Fuses　　The current fuse is a crucial safety device in electrical circuits. Its working principle is based on the thermal effect of current. When the current flowing through the fuse exceeds its rated value, the resistance of the fuse wire generates heat. According to Joule's law ($Q = I^{2}Rt$, where $Q$ is the heat generated, $I$ is the current, $R$ is the resistance, and $t$ is the time), as the current $I$ is large enough, the heat generated $Q$ will be sufficient to melt the fuse wire.　　In terms of application scenarios, current fuses are widely used in various electrical systems. In household electrical appliances, for example, they protect devices such as refrigerators, televisions, and microwaves. If there is a short - circuit or overload in the circuit of these appliances, the fuse will blow, preventing excessive current from damaging the internal components. In automotive electrical systems, current fuses safeguard t

September 09,2024

How to choose fuses for new energy products

　　　　Rated current: Firstly, it is very important to understand the rated current required for the product. The rated current should match the design and circuit requirements of the product itself. The rated current of the fuse should be slightly higher than the maximum operating current of the product to ensure the effectiveness of overload protection.　　Freeze voltage: Determine the voltage range used by the product, and consider its freeze voltage when selecting fuses. The freeze voltage of the fuse should be able to adapt to the highest voltage used by the product to prevent the fuse from breaking down when the voltage is too high.　　Melting characteristic: The melting characteristic of a fuse refers to its response speed in the event of overload or short circuit. Different application scenarios may require different types of fuse speeds. Some applications may require fast melting fuses to ensure timely circuit disconnection, while others may require fuses with delayed or slow melting

August 19,2024

fast blow fuse application

　　How to choose the appropriate fuse　　Choosing the appropriate fuse requires consideration of multiple factors, including the operating voltage, operating current, load type, and environmental conditions of the circuit. Here are some key steps when choosing a fuse:　　1. Determine the maximum current of the circuit: This is the basis for selecting the rated current of the fuse. The rated current of the fuse should be slightly greater than the maximum operating current of the circuit to avoid frequent melting.　　2. Consider the voltage of the circuit: The rated voltage of the fuse should be greater than or equal to the operating voltage of the circuit to ensure its normal operation.　　3. Choose the appropriate type: Select fuses of different types and specifications according to the specific needs of the circuit. For example, for inductive loads, slow melting fuses should be selected; For high-frequency circuits, fuses with fast response times should be selected.　　4. Consider environmental

September 29,2024

ambient air temperature sensor

　　Corrosion resistant fuses　　Corrosion resistant fuses provide critical protection for electronic devices in harsh chemical environments.　　In some special application scenarios, such as marine environments, chemical factories, sewage treatment facilities, etc., electronic devices are easily corroded by corrosive substances. These corrosive substances may damage the outer shell and internal components of the fuse, causing the fuse to fail and affecting the normal operation of the equipment. The emergence of corrosion-resistant fuses has effectively solved this problem.　　Corrosion resistant fuses typically use special materials and designs to resist the erosion of corrosive substances. The shell material generally has good corrosion resistance and can maintain structural integrity in harsh chemical environments. The internal molten material has also undergone special treatment to maintain stable melting characteristics in corrosive environments.　　In terms of structural design, corrosion-

October 22,2024

how to change a fuse box fuse

　　Adaptation of Current Fuses for Industrial Equipment　　Current fuses play a crucial role in protecting industrial equipment from electrical faults. When selecting and adapting current fuses for industrial applications, several factors need to be considered.　　First, the electrical characteristics of the equipment must be understood. This includes the voltage, current, and power requirements of the equipment. The fuse should be selected with an amperage rating that is appropriate for the maximum expected current flow in the circuit.　　Second, the operating environment of the industrial equipment is important. Industrial settings often involve harsh conditions such as high temperatures, dust, moisture, and vibration. The fuse should be able to withstand these conditions and continue to provide reliable protection.　　Third, the type of fuse and its installation method should be suitable for the specific application. There are different types of fuses available, including blade fuses, cartri